Pacific VP30 Hinged Door Set -/30/30sm

 

The VP30 is a Pyropanel FR board Maxi door.

The Pacific VP30 is a side hung door set. The door set configuration may be single leaf or pair, finished with a variety of facings and hung in a steel or timber frame.

Timber framed smoke control doors include a seal in the frame. Steel framed doors include the PFS-4 seal. If required, bottom seals can be selected from the hardware list.

The thickness of the VP30 door leaf is 48mm with an approximate base leaf weight of 27kg/m2

 Wall Type Jamb Type Fire Resistance Rating
Stability/Integrity/Insulation		 Door Application Max Leaf
Height (mm)		 Max Leaf
Width (mm)
 Steel Stud Wall
Timber Stud Wall
Masonry Wall		 Timber  -/30/30sm Single 2700 1020
Pair 2700 1020
 Steel Stud Wall
Timber Stud Wall
Masonry Wall		 Steel  -/30/30sm Single 3000 1500
Pair 3000 1500
Korok / Speedpanel Steel -/30/30sm Single & Pair 2400 1200
2700 1050
Korok Timber -/30/30sm Single 2197 920
James Hardie Steel -/30/30sm Single 2400 1020

Notes:

  1. Please note that the maximum leaf width shown above is measured per door leaf.
  2. The ‘sm’ above denotes that the door is available as a smoke control door set.
  3.  Meeting styles for doors installed into Korok walls are restricted to J-Section or Bullnose.
  4. Timber framed doorsets in Korok walls have limited installation options. Please see the installation section for details.
  5. Timber jambs are not possible for doors installed into James Hardie walls.
  6. Insulation ratings must be notified at time of pricing for steel frames.
  7. Door sets with leafs larger than 2700 x 1200 are not intended for frequent use, we recommend they be typically either held open or closed with compliant hardware in normal operation.
  8. Minimum width for a fire door leaf is governed by the need to fit a compliant closer. Typically, 400 mm is the practical minimum.

Product Options

Leaf Facings

  • MDF
  • Hardboard
  • Oil Tempered Hardboard
  • Plywood
  • Timber Veneers 
  • Acrylic - vinyl sheets up to 1.5mm thick (e.g. Acrovyn, Korogard)
  • Sheet Vinyl (1.25 – 2mm)
  • High pressure laminate
  • up to 1.5mm thick (e.g. Laminex, Formica)
  • Decorative timber mouldings/panels
  • Aluminium sheet (0.3 – 1mm) *
  • Metal Sheet, mild or stainless (0.6 – 1.0mm) *

Notes:

  1. Of the above facings only those marked * may extend around the door edge.
  2. Timber veneer requires FRR -/30/30 and is only available in timber frame or packed steel frame
  3. Steel frames are required where metal capping is used.
  4. Standard Paint Quality doors are allowed ‘non-clashed’ to provide best surface for finish painting.
  5. See Additional Door Options for more facing alternatives.

Leaf Edges

The leaf edges listed below are available for the VP30 door set.

Paint quality doors are non-clashed as standard.

   

Notes:

  1. Metal cappings are not available for timber framed doorsets or doors into Speedwall or James Hardie.

Frame Types & Profiles

Timber Frame

The timber frame profiles listed below are available for the VP30 door set.

The timber species of the frame must be a hardwood of minimum density 580kg/m3

 

Steel Frame

The steel frame profiles listed below are available for the VP30 door set.

The VP30 door set is available in the two-part steel frame system for fixing to walls already lined.

 

Notes:

  1. D2 and D4 not available for doors with sidelights or overlights, and is not compliant in Speedwall.

  2. D2 and D4 require minimum 110 mm wall thickness

Standard frames are three-sided only with no sill. Four-sided frames and/or custom sills may be available on request. Timber sills are not available on fire doorsets. For more in depth information on frame profiles and sizes, please see our Installation Instructions.

Meeting Stiles

The meeting stiles listed below are applicable to paired door sets only.

Acoustical performance

An acoustic rating of STC 31 (Rw 32) is available for ply / MDF faced doors and STC 36 (Rw 38) for steel face doors.

If an acoustic rating is required this has to be specified at time of order and will come with restrictions around seals and vision panels. Please contact Pacific Doors if more information is required.

Wall Types

As previously noted, Jambs may be connected to timber stud, steel stud or concrete/masonry walls. The minimum specification for each wall type is:

  • Precast Concrete of 100mm thickness minimum or grouted blockwork of 140mm thickness minimum.
  • Timber or steel stud plasterboard walls of FRR -/30/30 or above. Where steel framed door sets are used, wall framing must be 100 x 50mm minimum.
  • Universal Wall systems GBUW30a or GBUW30b
  • Gib Weatherline Rigid Air Barrier Systems GWTLE 30 and GWTLP 30
  • Speedpanel & Korok walls (51mm, 64mm or 78mm)
  • James Hardie JHETGJ60 fire rated wall system.
  • Boral 25mm shaftliner wall (Note special installation details and size restrictions apply refer Pacific Doors for details)

Product Optional Extras

Vision Panels

Glazing Type Maximum Glazed Area Max Height (mm) Max Width (mm) Glazing Bead FRR with Vision Panel
Per VP Total Timber Aluminum Up to 0.065m2 Over 0.065m2
Pyrobel* 0.6m2 0.96m2 1630 950 √ √ -/30/30 -/30/30
Georgian Wired 0.32m2 0.32m2 850 950 √ √ -/30/30 -/30/-
Firelite 0.32m2 0.32m2 850 950 √ √ -/30/30 -/30/-
Robax 0.32m2 0.32m2 850 950 √ √ -/30/30 -/30/-
Pyran* 0.32m2 0.32m2 850 950 √ √ -/30/30 -/30/-

Notes:

  1. Please note that the height and width of the vision panel must still fall within the maximum glazed area.
  2. A maximum of two vision panels are permitted per leaf.
  3. Glazing types marked with * indicate Grade A Safety glass.
  4. Circular vision panels are not possible with Pyrobel glazing.
  5. Pyrobel is not suitable for exterior doors.

 

Glazing details for Pyrobel glazed vision panels

 

Glazing details for other glazing types

Circular Vision Panels

Circular vision panels are not currently offered for this product.

Standard Vision Panel Cross Sections

Timber Bead

Timber Bead*

*Pyrobel only

Aluminium Bead

Sidelights and Overlights - Pyrobel glazing - FRR -/30/30

Timber Framed Sidelight & Overlight

Elevation

The Pyrobel glazing system can include panes of up to 2537h or 2537w, up to a maximum glazed area of 3.70m2

Pyrobel is not suitable for exterior use.

Detail

For the VP30 system, the separate glazed sidelight is connected to the fire door frame with a layer of 13mm plasterboard between. The joint is covered by a timber architrave as illustrated below. Door set, sidelite and overlite will be made and dispatched separately for on site assembly. 13mm Fyreline and architraves not supplied by Pacific Doors.

Sidelights & overlights are not available in Korok walls.

 

 

Steel Framed Sidelight & Overlight

Elevation

The steel framed glazing system can include panes of up to 2820h or 2820w, up to a maximum glazed area of 3.58m2

Detail

The steel frame between the window and the door must be packed with fire insulation board. Unit is required to be factory welded therefore practical limitations of size need to be considered for freight. Powder coat finish is not available.

Sidelights & overlights are not available in Korok walls.

 

Note: Pyrobel glazing can be used for interior applications only.

Sidelights and Overlights - Other glazing types - FRR -/30/-

Timber Frame - Uninsulated Sidelights and Overlights

Restrictions

Maximum height of overall unit is 2500mm.

This sidelight and overlight configuration is available for single and paired door sets, however the maximum height and width of the door set is 2400h x 1050w when a sidelight and/or overlight is added.

This sidelight and overlight configuration applies to the following uninsulated glazing types:

  • Firelite
  • Georgian Wired
  • Robax
  • Pyran

Clear pane size of 967h x 558w for all applicable glazing types.

Sidelights & overlights are not available in Korok walls.

 

 

Steel Frame - Uninsulated Sidelights and Overlights

                                                               

Restrictions

Maximum height of overall unit is 3100mm.

This sidelight and overlight configuration is available for single and paired door sets, however the maximum height and width of the door set is 2400h x 1200w when a sidelight and/or overlight is added.

This sidelight and overlight configuration applies to the following uninsulated glazing types:

  • Firelite
  • Georgian Wired
  • Robax
  • Pyran

Clear pane size of 600h x 1630w for all applicable glazing types.

Sidelights & overlights are not available in Korok walls.

 

 

Overpanels

Overpanel With Transom Elevations in Steel Frame

Overpanels with transom are available in steel jambs to an overall height of 4160mm both in single leaf and pair door sets.
 

   

Steel Transom Overpanel Detail

Fixed side panels may be fitted as part of this door set in a steel frame.

Sidelights, Overlights and Panels are not permitted in Korok / Speedwall or James Hardie wall.

Additional Door Options

Push or Kickplates

Push plates or kickplates can be of the below permitted materials and can be either surface mounted or recessed flush. Fixing may be via screws or contact adhesive only.

  • Steel (mild or Stainless)
  • Vinyl Sheets up to 2mm
  • Formica
  • Acrovyn 4000
  • Korogard

Rubber kickplates can only be surface mounted – special conditions do apply, please contact us for more detail.
 

Ventilation Grilles

 

 

Lorient LVH intumescent grilles are available in the following sizes:

  • 300 x 300 mm
  • 450 x 450 mm
  • 600 x 300 mm
  • 600 x 600 mm

Two such Intumescent grilles may be fitted to each leaf separated from each other and hardware by at least 300mm (only one 600 x 600 mm grille allowed per leaf).

Ventilation grilles are not suitable for exposed exterior doors. Grilles in exterior doors require an additional, custom made cover plate.

Please note that fire doors with ventilation grilles cannot be certified as ‘Smoke control' door sets.

Drop shutter grilles are not an option on this doorset.

 

Sloping/Raked Head Fire Door

The VP30 leaf is available with a raked top edge. The length of the inclined edge must not exceed 1200mm.
 

Adjacent Doors

Adjacent fire rated doors are permitted provided the central mullion is grouted steel or else timber (100 x 75mm lined with Fyreline Gib Board 13mm each side or hardwood 60 x 115mm minimum without linings).

Adjacent fire rated doors are not permitted in Speedwall or James Hardie walls.
 

V-GROOVES

V-grooves can be machined into the leaf facings for aesthetic purposes.

The following restrictions apply:

  • Leaf facing has to be MDF or ply

       

Decorative panels

Decorative panels (stone, glass, MDF, plasterboard, hardboard or greenboard) can be added to one face of the door leaf provided:

•    Panel is glue fixed (no screws or nails)
•    Additional weight is less than 20 kg per hinge
•    Leaf dimensions are 2400 x 1020 or less
•    Leaf is hung in a steel frame

Panels to be installed on site by others. They can be either glued directly to the face of the leaf or onto timber battens glued to the leaf.

If the decorative panel is on the hinge face of the leaf, please specify extended "wide throw" hinges.
Decorative panels on push face of leaf may not extend under the frame stop.
Please note that special hardware items may be required (e.g. extended spindles).
Decorative panels are not allowed in conjunction with vision panels.

 

Thermal Insulation

This door leaf has a thermal insulation rating (R-value) of 0.645 Km2/W.

Acoustical performance graphs

Plywood or MDF faces: Rw 32 / STC 31:

Steel faces: Rw 38 / STC 36:

Building Product Information Statement