Installation Instructions

Frame materials available:

• Timber (any species), Pine clear standard

Recommended Fasteners:

• Frame - Either nailed (75 x 3.2mm) or screwed (10g x 75mm) at 600mm centres nominal. Two fixings per location.
• Stops - nailed (50 x 3.2mm) at 200mm centres.
• Architrave - nailed (50 x 3.2mm) at 400mm centres.
• Pryda Jamb-fixa brackets Type JFB100 at 500mm centres may be used.

Head Fixing (minimum):

• Single door - none required
• Paired door - double central fastener required

Stud size:

• Stud to suit acoustic wall system of equal or greater rating required

Wedging gap:

• 0-10mm

Frame materials available:

• EGZ - 1.6mm
• Cold rolled galvanized - 1.6mm
• Stainless Steel - 1.5mm

Fasteners:

• Framing stud No.1 screwed to jamb.
• Connection to stud No.2 via rebated nail on plates. One fastener per location except at bottom where two fasteners are required.
• Frame to be screw fixed (10g x 50mm self tapping) at 600mm nominal centres. Two fasteners per location where applicable.

Head Fixing (minimum):

• Single door - none required
• Paired door - double central fastener required

Stud size:

• Stud to suit acoustic wall system of equal or greater rating required

Wedging gap:

• Not applicable

Frame materials available:

• EGZ - 1.6mm
• Cold rolled galvanized - 1.6mm
• Stainless Steel - 1.5mm

Fasteners:

• Frames may be screwed directly to studs either through the stud and into the frame bracing straps or through the frame into the timber stud at 600mm centres nominal.
• Frame to be screw fixed (10g x 50mm self tapping) at 600mm centres nominal. Two fasteners per location where applicable.

Head Fixing (minimum):

• Single door - none required
• Paired door - double central fastener required

Stud size:

• Stud to suit acoustic wall system of equal or greater rating required

Wedging gap:

• Not applicable

Frame materials available:

• Timber (any species), Pine clear standard

Fasteners:

• Frame - M8 or M10 'Ramset' Dynabolts at 600mm centres nominal and near hinges. Fixings on or near centre of frame jamb.
• Stops - nailed (50 x 3.2mm) at 200mm centres.
• Architrave - nailed (50 x 3.2mm) at 400mm centres.

Head Fixing (minimum):

• Single door - none required
• Paired door - single central fastener required

Wedging gap:

• 0-10mm

Frame materials available:

• Timber (any species), Pine clear standard

Fasteners:

• Frame - Screwed (10g x 50mm self tapping) at 600mm centres nominal. Minimum of one screw per location.
• Frames may also be installed by screw fixing the steel studs to the back of the timber frame during wall construction.
• Stops - nailed (50 x 3.2mm) at 200mm centres.
• Architrave - nailed (50 x 3.2mm) at 400mm centres.

Head Fixing (minimum):

• Single door - none required
• Paired door - double central fastener required

Stud size:

• Stud to suit acoustic wall system of equal or greater rating required

Wedging gap:

• 0-10mm

Frame materials available:

• Timber (any species), Pine clear standard

Recommended Fasteners:

• Frame - Screwed (10g x 50mm self tapping) at 600mm centres nominal. Minimum of one screw per location. Frames may also be installed by screw fixing the steel studs to the back of the timber frame during wall construction.
• Stops - nailed (50 x 3.2mm) at 200mm centres.
• Architrave - nailed (50 x 3.2mm) at 400mm centres.

Head Fixing (minimum):

• Single door - none required
• Paired door - double central fastener required

Stud size:

• Stud to suit acoustic wall system of equal or greater rating required

Wedging gap:

• 0-10mm

Frame materials available:

• EGZ - 1.6mm
• Cold rolled galvanized - 1.6mm
• Stainless Steel - 1.5mm

Fasteners:

• Frame screwed to boxed stud at 600mm centres nominal with self tapping screws.
• Steel studs may be riveted (steel pop rivets) or screwed (9g x 45mm self tapping) to the frame bracing straps at 600mm centres nominal.

Head Fixing (minimum):

• Single door - none required
• Paired door - double central fastener required

Stud size:

• Stud to suit acoustic wall system of equal or greater rating required

Wedging gap:

• Not applicable

Frame materials available:

• EGZ - 1.6mm
• Cold rolled galvanized - 1.6mm
• Stainless Steel - 1.5mm

Fasteners:

• Frame screwed to boxed studs with packing steel shims at 600mm centres nominal.
• Steel studs to be screwed (9g x 75mm self tapping) to the frame bracing straps at 600mm centres nominal.

Head Fixing (minimum):

• Single door - none required
• Paired door - double central fastener required

Stud size:

• Stud to suit acoustic wall system of equal or greater rating required

Wedging Gap:

• 0-10mm

Frame materials available:

• Timber (any species), Pine clear standard

Recommended Fasteners:

• Frame - Either nailed (75 x 3.2mm) or screwed (10g x 75mm) at 600mm centres nominal. Two fixings per location.
• Stops - nailed (50 x 3.2mm) at 200mm centres.
• Architrave - nailed (50 x 3.2mm) at 400mm centres.
• Pryda Jamb-fixa brackets Type JFB100 at 500mm centres may be used.

Head Fixing (minimum):

• Single door - none required
• Paired door - double central fastener required

Stud size:

• Stud to suit acoustic wall system of equal or greater rating required

Wedging gap:

• 0-10mm

Frame materials available:

• EGZ - 1.6mm
• Cold rolled galvanized - 1.6mm
• Stainless Steel - 1.5mm

Fasteners:

• Framing stud No.1 screwed to jamb.
• Connection to stud No.2 via rebated nail on plates. One fastener per location except at bottom where two fasteners are required.
• Frame to be screw fixed (10g x 50mm self tapping) at 600mm nominal centres. Two fasteners per location where applicable.

Head Fixing (minimum):

• Single door - none required
• Paired door - double central fastener required

Stud size:

• Stud to suit acoustic wall system of equal or greater rating required

Wedging gap:

• Not applicable

Frame materials available:

• EGZ - 1.6mm
• Cold rolled galvanized - 1.6mm
• Stainless Steel - 1.5mm

Fasteners:

• Frames may be screwed directly to studs either through the stud and into the frame bracing straps or through the frame into the timber stud at 600mm centres nominal.
• Frame to be screw fixed (10g x 50mm self tapping) at 600mm centres nominal. Two fasteners per location where applicable.

Head Fixing (minimum):

• Single door - none required
• Paired door - double central fastener required

Stud size:

• Stud to suit acoustic wall system of equal or greater rating required

Wedging gap:

• Not applicable

Frame materials available:

• Timber (any species), Pine clear standard

Fasteners:

• Frame - M8 or M10 'Ramset' Dynabolts at 600mm centres nominal and near hinges. Fixings on or near centre of frame jamb.
• Stops - nailed (50 x 3.2mm) at 200mm centres.
• Architrave - nailed (50 x 3.2mm) at 400mm centres.

Head Fixing (minimum):

• Single door - none required
• Paired door - single central fastener required

Wedging gap:

• 0-10mm

Frame materials available:

• Timber (any species), Pine clear standard

Fasteners:

• Frame - Screwed (10g x 50mm self tapping) at 600mm centres nominal. Minimum of one screw per location.
• Frames may also be installed by screw fixing the steel studs to the back of the timber frame during wall construction.
• Stops - nailed (50 x 3.2mm) at 200mm centres.
• Architrave - nailed (50 x 3.2mm) at 400mm centres.

Head Fixing (minimum):

• Single door - none required
• Paired door - double central fastener required

Stud size:

• Stud to suit acoustic wall system of equal or greater rating required

Wedging gap:

• 0-10mm

Frame materials available:

• Timber (any species), Pine clear standard

Recommended Fasteners:

• Frame - Screwed (10g x 50mm self tapping) at 600mm centres nominal. Minimum of one screw per location. Frames may also be installed by screw fixing the steel studs to the back of the timber frame during wall construction.
• Stops - nailed (50 x 3.2mm) at 200mm centres.
• Architrave - nailed (50 x 3.2mm) at 400mm centres.

Head Fixing (minimum):

• Single door - none required
• Paired door - double central fastener required

Stud size:

• Stud to suit acoustic wall system of equal or greater rating required

Wedging gap:

• 0-10mm

Frame materials available:

• EGZ - 1.6mm
• Cold rolled galvanized - 1.6mm
• Stainless Steel - 1.5mm

Fasteners:

• Frame screwed to boxed stud at 600mm centres nominal with self tapping screws.
• Steel studs may be riveted (steel pop rivets) or screwed (9g x 45mm self tapping) to the frame bracing straps at 600mm centres nominal.

Head Fixing (minimum):

• Single door - none required
• Paired door - double central fastener required

Stud size:

• Stud to suit acoustic wall system of equal or greater rating required

Wedging gap:

• Not applicable

Frame materials available:

• EGZ - 1.6mm
• Cold rolled galvanized - 1.6mm
• Stainless Steel - 1.5mm

Fasteners:

• Frame screwed to boxed studs with packing steel shims at 600mm centres nominal.
• Steel studs to be screwed (9g x 75mm self tapping) to the frame bracing straps at 600mm centres nominal.

Head Fixing (minimum):

• Single door - none required
• Paired door - double central fastener required

Stud size:

• Stud to suit acoustic wall system of equal or greater rating required

Wedging Gap:

• 0-10mm

Frame materials available:

• Timber (any species), Pine clear standard

Fasteners:

• Frame - M8 or M10 'Ramset' Dynabolts at 600mm centres nominal and near hinges. Fixings on or near centre of frame jamb.
• Stops - nailed (50 x 3.2mm) at 200mm centres.
• Architrave - nailed (50 x 3.2mm) at 400mm centres.

Head Fixing (minimum):

• Single door - none required
• Paired door - single central fastener required

Wedging gap:

• 0-10mm

Frame materials available:

• Timber (any species), Pine clear standard

Fasteners:

• Frame - Screwed (10g x 50mm self tapping) at 600mm centres nominal. Minimum of one screw per location.
• Frames may also be installed by screw fixing the steel studs to the back of the timber frame during wall construction.
• Stops - nailed (50 x 3.2mm) at 200mm centres.
• Architrave - nailed (50 x 3.2mm) at 400mm centres.

Head Fixing (minimum):

• Single door - none required
• Paired door - double central fastener required

Stud size:

• Stud to suit acoustic wall system of equal or greater rating required

Wedging gap:

• 0-10mm

Frame materials available:

• EGZ - 1.6mm
• Cold rolled galvanized - 1.6mm
• Stainless Steel - 1.5mm

Fasteners:

• Frame screwed to boxed stud at 600mm centres nominal with self tapping screws.
• Steel studs may be riveted (steel pop rivets) or screwed (9g x 45mm self tapping) to the frame bracing straps at 600mm centres nominal.

Head Fixing (minimum):

• Single door - none required
• Paired door - double central fastener required

Stud size:

• Stud to suit acoustic wall system of equal or greater rating required

Wedging gap:

• Not applicable

Frame materials available:

• EGZ - 1.6mm
• Cold rolled galvanized - 1.6mm
• Stainless Steel - 1.5mm

Fasteners:

• Frame screwed to boxed studs with packing steel shims at 600mm centres nominal.
• Steel studs may be riveted (steel pop rivets) or screwed (9g x 45mm self tapping) to the frame bracing straps at 600mm centres nominal.

Head Fixing (minimum):

• Single door - none required
• Paired door - double central fastener required

Stud size:

• Stud to suit acoustic wall system of equal or greater rating required

Wedging Gap:

• 0-10mm

Frame materials available:

• Timber (any species), Pine clear standard

Recommended Fasteners:

• Frame - Either nailed (75 x 3.2mm) or screwed (10g x 75mm) at 600mm centres nominal. Two fixings per location.
• Stops - nailed (50 x 3.2mm) at 200mm centres.
• Architrave - nailed (50 x 3.2mm) at 400mm centres.
• Pryda Jamb-fixa brackets Type JFB100 at 500mm centres may be used.

Head Fixing (minimum):

• Single door - none required
• Paired door - double central fastener required

Stud size:

• Stud to suit acoustic wall system of equal or greater rating required

Wedging gap:

• 0-10mm

Frame materials available:

• EGZ - 1.6mm
• Cold rolled galvanized - 1.6mm
• Stainless Steel - 1.5mm

Fasteners:

• Framing stud No.1 screwed to jamb.
• Connection to stud No.2 via rebated nail on plates. One fastener per location except at bottom where two fasteners are required.
• Frame to be screw fixed (10g x 50mm self tapping) at 600mm nominal centres. Two fasteners per location where applicable.

Head Fixing (minimum):

• Single door - none required
• Paired door - double central fastener required

Stud size:

• Stud to suit acoustic wall system of equal or greater rating required

Wedging gap:

• Not applicable

Frame materials available:

• EGZ - 1.6mm
• Cold rolled galvanized - 1.6mm
• Stainless Steel - 1.5mm

Fasteners:

• Frames may be screwed directly to studs either through the stud and into the frame bracing straps or through the frame into the timber stud at 600mm centres nominal.
• Frame to be screw fixed (10g x 50mm self tapping) at 600mm centres nominal. Two fasteners per location where applicable.

Head Fixing (minimum):

• Single door - none required
• Paired door - double central fastener required

Stud size:

• Stud to suit acoustic wall system of equal or greater rating required

Wedging gap:

• Not applicable

Frame materials available:

• Timber (any species), Pine clear standard

Fasteners:

• Frame - M8 or M10 'Ramset' Dynabolts at 600mm centres nominal and near hinges. Fixings on or near centre of frame jamb.
• Stops - nailed (50 x 3.2mm) at 200mm centres.
• Architrave - nailed (50 x 3.2mm) at 400mm centres.

Head Fixing (minimum):

• Single door - none required
• Paired door - single central fastener required

Wedging gap:

• 0-10mm

Frame materials available:

• Timber (any species), Pine clear standard

Fasteners:

• Frame - Screwed (10g x 50mm self tapping) at 600mm centres nominal. Minimum of one screw per location.
• Frames may also be installed by screw fixing the steel studs to the back of the timber frame during wall construction.
• Stops - nailed (50 x 3.2mm) at 200mm centres.
• Architrave - nailed (50 x 3.2mm) at 400mm centres.

Head Fixing (minimum):

• Single door - none required
• Paired door - double central fastener required

Stud size:

• Stud to suit acoustic wall system of equal or greater rating required

Wedging gap:

• 0-10mm

Frame materials available:

• Timber (any species), Pine clear standard

Recommended Fasteners:

• Frame - Screwed (10g x 50mm self tapping) at 600mm centres nominal. Minimum of one screw per location. Frames may also be installed by screw fixing the steel studs to the back of the timber frame during wall construction.
• Stops - nailed (50 x 3.2mm) at 200mm centres.
• Architrave - nailed (50 x 3.2mm) at 400mm centres.

Head Fixing (minimum):

• Single door - none required
• Paired door - double central fastener required

Stud size:

• Stud to suit acoustic wall system of equal or greater rating required

Wedging gap:

• 0-10mm

Frame materials available:

• EGZ - 1.6mm
• Cold rolled galvanized - 1.6mm
• Stainless Steel - 1.5mm

Fasteners:

• Frame screwed to boxed stud at 600mm centres nominal with self tapping screws.
• Steel studs may be riveted (steel pop rivets) or screwed (9g x 45mm self tapping) to the frame bracing straps at 600mm centres nominal.

Head Fixing (minimum):

• Single door - none required
• Paired door - double central fastener required

Stud size:

• Stud to suit acoustic wall system of equal or greater rating required

Wedging gap:

• Not applicable

Frame materials available:

• EGZ - 1.6mm
• Cold rolled galvanized - 1.6mm
• Stainless Steel - 1.5mm

Fasteners:

• Frame screwed to boxed studs with packing steel shims at 600mm centres nominal.
• Steel studs to be screwed (9g x 75mm self tapping) to the frame bracing straps at 600mm centres nominal.

Head Fixing (minimum):

• Single door - none required
• Paired door - double central fastener required

Stud size:

• Stud to suit acoustic wall system of equal or greater rating required

Wedging Gap:

• 0-10mm

Frame materials available:

• Hardwood timber - Min density 650kg/m³
• 42 mm or 30 mm timber jamb thickness

Fasteners:

• Frame - Either nailed (75 x3.2mm) or screwed (10g x 75mm) at 60mm centres nominal. Two fixings per location.
• Stops - nailed (50 x 3.2mm) at 200mm centres.
• Architrave - nailed (50 x 3.2mm) at 400mm centres.
• Pryda Jamb-fixa brackets type JFB100 at 500mm centres may be used.

Head Fixing

• Single door - none required.
• Paired door - double central fastener required.

Stud Size

• Stud to suit acoustic wall system of equal or greater rating required.

Wedging gap:

• 0-10mm

Frame materials available:

• Timber (any species), Pine clear standard

Recommended Fasteners:

• Frame - Either nailed (75 x 3.2mm) or screwed (10g x 75mm) at 600mm centres nominal. Two fixings per location.
• Stops - nailed (50 x 3.2mm) at 200mm centres.
• Architrave - nailed (50 x 3.2mm) at 400mm centres.
• Pryda Jamb-fixa brackets Type JFB100 at 500mm centres may be used.

Head Fixing (minimum):

• Single door - none required
• Paired door - double central fastener required

Stud size:

• Stud to suit acoustic wall system of equal or greater rating required

Wedging gap:

• 0-10mm

Frame materials available:

• EGZ - 1.6mm
• Cold rolled galvanized - 1.6mm
• Stainless Steel - 1.5mm

Fasteners:

• Framing stud No.1 screwed to jamb.
• Connection to stud No.2 via rebated nail on plates. One fastener per location except at bottom where two fasteners are required.
• Frame to be screw fixed (10g x 50mm self tapping) at 600mm nominal centres. Two fasteners per location where applicable.

Head Fixing (minimum):

• Single door - none required
• Paired door - double central fastener required

Stud size:

• Stud to suit acoustic wall system of equal or greater rating required

Wedging gap:

• Not applicable

Frame materials available:

• EGZ - 1.6mm
• Cold rolled galvanized - 1.6mm
• Stainless Steel - 1.5mm

Fasteners:

• Frames may be screwed directly to studs either through the stud and into the frame bracing straps or through the frame into the timber stud at 600mm centres nominal.
• Frame to be screw fixed (10g x 50mm self tapping) at 600mm centres nominal. Two fasteners per location where applicable.

Head Fixing (minimum):

• Single door - none required
• Paired door - double central fastener required

Stud size:

• Stud to suit acoustic wall system of equal or greater rating required

Wedging gap:

• Not applicable

Frame materials available:

• Timber (any species), Pine clear standard

Fasteners:

• Frame - M8 or M10 'Ramset' Dynabolts at 600mm centres nominal and near hinges. Fixings on or near centre of frame jamb.
• Stops - nailed (50 x 3.2mm) at 200mm centres.
• Architrave - nailed (50 x 3.2mm) at 400mm centres.

Head Fixing (minimum):

• Single door - none required
• Paired door - single central fastener required

Wedging gap:

• 0-10mm

Frame materials available:

• Timber (any species), Pine clear standard

Fasteners:

• Frame - Screwed (10g x 50mm self tapping) at 600mm centres nominal. Minimum of one screw per location.
• Frames may also be installed by screw fixing the steel studs to the back of the timber frame during wall construction.
• Stops - nailed (50 x 3.2mm) at 200mm centres.
• Architrave - nailed (50 x 3.2mm) at 400mm centres.

Head Fixing (minimum):

• Single door - none required
• Paired door - double central fastener required

Stud size:

• Stud to suit acoustic wall system of equal or greater rating required

Wedging gap:

• 0-10mm

Frame materials available:

• Timber (any species), Pine clear standard

Recommended Fasteners:

• Frame - Screwed (10g x 50mm self tapping) at 600mm centres nominal. Minimum of one screw per location. Frames may also be installed by screw fixing the steel studs to the back of the timber frame during wall construction.
• Stops - nailed (50 x 3.2mm) at 200mm centres.
• Architrave - nailed (50 x 3.2mm) at 400mm centres.

Head Fixing (minimum):

• Single door - none required
• Paired door - double central fastener required

Stud size:

• Stud to suit acoustic wall system of equal or greater rating required

Wedging gap:

• 0-10mm

Frame materials available:

• EGZ - 1.6mm
• Cold rolled galvanized - 1.6mm
• Stainless Steel - 1.5mm

Fasteners:

• Frame screwed to boxed stud at 600mm centres nominal with self tapping screws.
• Steel studs may be riveted (steel pop rivets) or screwed (9g x 45mm self tapping) to the frame bracing straps at 600mm centres nominal.

Head Fixing (minimum):

• Single door - none required
• Paired door - double central fastener required

Stud size:

• Stud to suit acoustic wall system of equal or greater rating required

Wedging gap:

• Not applicable

Frame materials available:

• EGZ - 1.6mm
• Cold rolled galvanized - 1.6mm
• Stainless Steel - 1.5mm

Fasteners:

• Frame screwed to boxed studs with packing steel shims at 600mm centres nominal.
• Steel studs to be screwed (9g x 75mm self tapping) to the frame bracing straps at 600mm centres nominal.

Head Fixing (minimum):

• Single door - none required
• Paired door - double central fastener required

Stud size:

• Stud to suit acoustic wall system of equal or greater rating required

Wedging Gap:

• 0-10mm

Frame materials available:

• Timber (any species), Pine clear standard

Fasteners:

• Frame - Either nailed (75 x 3.2mm) or screwed (10g x 75mm) at 600mm centres nominal. Two fixings per location.

Stops - nailed (50 x 3.2mm) at 200mm centres.

Architrave - nailed (50 x 3.2mm) at 400mm centres.

• Pryda Jamb-fixa brackets Type JFB100 at 500mm centres may be used.

Head Fixing (minimum):

• Single door - none required
• Paired door - double central fastener required

Wedging gap:

• 0-10mm

Frame materials available:

• EGZ - 1.6mm
• Cold rolled galvanized - 1.6mm
• Stainless Steel - 1.5mm

Fasteners:

• Frames may be screwed directly to studs either through the stud and into the frame bracing straps or through the frame into the timber stud at 600mm centres nominal.
• Frame to be screw fixed (10g x 50mm self tapping) at 600mm centres nominal. Two fasteners per location where applicable.

Head Fixing (minimum):

• Single door - none required
• Paired door - double central fastener required

Stud size:

• Ex 100 x 50 minimum

Wedging gap:

• 0-10mm

Frame materials available:

• EGZ - 1.6mm
• Cold rolled galvanized - 1.6mm
• Stainless Steel - 1.5mm

Fasteners:

• Frame to be screw fixed (10g self tapping) at 600mm centres nominal. Two fasteners per location where applicable.

Head Fixing (minimum)

• Single door - none required
• Paired door - single central fixing required

Stud Size:

• Ex 100 x50 minimum

Wedging gap:

• 0-10mm

Frame materials available:

• Hardwood timber - Min. density 580kg/m≥ (minimum thickness is 30mm)

Fasteners:

• Frame - M8 or M10 'Ramset' Dynabolts at 600mm centres nominal. Fixings on or near centre of frame jamb.
• Stops - nailed (50 x 3.2mm) at 200mm centres.
• Architrave - nailed (50 x 3.2mm) at 400mm centres.

Head Fixing (minimum):

• Single door - none required
• Paired door - single central fastener required

Wedging gap:

• 0-15mm

Frame materials available:

• Forster extruded profile

Fasteners:

• 12g screws at 450mm centres maximum

Wedging gap:

• 0-10mm

Frame materials available:

• Forster extruded profile

Fasteners:

• M8 masonry bolts at 450mm centres maximum

Wedging gap:

• 0-10mm

Frame materials available:

• Forster extruded profile

Fasteners:

• M8 masonry bolts at 450mm centres maximum

Wedging gap:

• 0-10mm