Installation Instructions

Frame materials available:

• Hardwood timber - Min density 650kg/m³
• 42 mm or 30 mm timber jamb thickness

Fasteners:

• Frame - Either nailed (75 x3.2mm) or screwed (10g x 75mm) at 60mm centres nominal. Two fixings per location.
• Stops - nailed (50 x 3.2mm) at 200mm centres.
• Architrave - nailed (50 x 3.2mm) at 400mm centres.
• Pryda Jamb-fixa brackets type JFB100 at 500mm centres may be used.

Head Fixing

• Single door - none required.
• Paired door - double central fastener required.

Stud Size

• Stud to suit acoustic wall system of equal or greater rating required.

Wedging gap:

• 0-10mm

Frame materials available:

• Hardwood timber - Min. density 580kg/m≥ (minimum thickness is 30mm)

Fasteners:

• Frame - Either nailed (75 x 3.2mm) or screwed (10g x 75mm) at 600mm centres nominal. Two fixings per location.
• Stops - nailed (50 x 3.2mm) at 200mm centres.
• Architrave - nailed (50 x 3.2mm) at 400mm centres.
• Pryda Jamb-fixa brackets Type JFB100 at 500mm centres may be used to fix to approved walls.

Head Fixing (minimum):

• Single door - none required
• Paired door - double central fastener required

Stud size:

• Ex100 x 50 minimum.

Wedging gap:

• 0-10mm

Frame materials available:

• EGZ - 1.6mm
• Cold rolled galvanized - 1.6mm
• Stainless Steel - 1.5mm

Fasteners:

• Frame to be screw fixed (10g self tapping) at 600mm centres nominal. Two fasteners per location where applicable.

Head Fixing (minimum):

• Single door - none required
• Paired door - single central fastener required

Stud size:

• Ex 100x50 minimum.

Wedging gap:

• 0-10mm

Frame materials available:

• Hardwood timber - Min. density 580kg/m≥ (minimum thickness is 30mm)

Fasteners:

• Frame - M8 or M10 'Ramset' Dynabolts at 600mm centres nominal. Fixings on or near centre of frame jamb.
• Stops - nailed (50 x 3.2mm) at 200mm centres.
• Architrave - nailed (50 x 3.2mm) at 400mm centres.

Head Fixing (minimum):

• Single door - none required
• Paired door - single central fastener required

Wedging gap:

• 0-15mm

Frame materials available:

• EGZ - 1.6mm
• Cold rolled galvanized - 1.6mm
• Stainless Steel - 1.5mm

Fasteners:

• Jamb fixing at 600mm centres nominal
• Expansion anchors eg. M10 countersunk 'Ramset' Dynabolts
• M12 countersunk masonry screwbolts

Head Fixing (minimum):

• Single door - none required
• Paired door - single central fastener required

Wedging Gap:

• 0-10mm

Frame materials available:

• Timber (any species), Pine clear standard

Fasteners:

• Frame - Either nailed (75 x 3.2mm) or screwed (10g x 75mm) at 600mm centres. Two fixings per location.
• Stops - nailed (50 x 3.2mm) at 200mm centres.
• Architrave - nailed (50 x 3.2mm) at 400mm centres.
• Pryda Jamb-fixa brackets Type JFB100 at 500mm centres may be used.

Head Fixing (minimum):

• Single door - none required
• Paired door - Double central fastener required

Wedging gap:

• 0-10mm

Frame materials available:

• Timber (any species), Pine clear standard

Fasteners:

• Frame - Either nailed (75 x 3.2mm) or screwed (10g x 75mm) at 600mm centres. Two fixings per location.
• Stops - nailed (50 x 3.2mm) at 200mm centres.
• Architrave - nailed (50 x 3.2mm) at 400mm centres.
• Pryda Jamb-fixa brackets Type JFB100 at 500mm centres may be used.

Head Fixing (minimum):

• Single door - none required
• Paired door - single central fastener required

Wedging gap:

• 0-10mm

Frame materials available:

• EGZ - 1.6mm
• Cold rolled galvanized - 1.6mm
• Stainless Steel - 1.5mm

Fasteners:

• Framing stud No.1 screwed to jamb.
• Connection to stud No.2 via rebated nail on plates. One fastener per location except at bottom where two fasteners are required.
• Frame to be screw fixed (10g x 50mm self tapping) at 600mm nominal centres. Two fasteners per location where applicable.

Head Fixing (minimum):

• Single door - none required
• Paired door - single central fastener required

Wedging Gap:

• N/A

Frame materials available:

• EGZ - 1.6mm
• Cold rolled galvanized - 1.6mm
• Stainless Steel - 1.5mm

Fasteners:

• Frames may be screwed directly to studs either through the stud and into the frame bracing straps or through the frame into the timber stud at 600mm nominal centres.
• Frame to be screw fixed (10g x 50mm self tapping) at 600mm min. centres. Two fasteners per location where applicable to each strap.

Head Fixing (minimum):

• Single door - none required
• Paired door - single central fastener required

Wedging Gap:

• 0-15mm

Frame materials available:

• Timber (any species), Pine clear standard

Fasteners:

• Frame - M8 or M10 'Ramset' Dynabolts at 600mm centres and near hinges. Fixings on or near centre of frame jamb.
• Stops - nailed (50 x 3.2mm) at 200mm centres.
• Architrave - nailed (50 x 3.2mm) at 400 centres.

Head Fixing (minimum):

• Single door - none required
• Paired door - single central fastener required

Wedging gap:

• 0-15mm

Frame materials available:

• Timber (any species), Pine clear standard

Fasteners:

• Frame - Screwed (10g x 50mm self tapping) at 600mm nominal centres. Minimum of one screw per location. Frames may also be installed by screw fixing the steel studs to the back of the timber frame during wall construction.
• Stops - nailed (50 x 3.2mm) at 200mm centres.
• Architrave - nailed (50 x 3.2mm) at 400mm centres.

Head Fixing (minimum):

• Single door - none required
• Paired door - single central fastener required

Wedging gap:

• 0-10mm

Frame materials available:

• Timber (any species), Pine clear standard

Fasteners:

• Frame - Screwed (10g x 50mm self tapping) at 600mm nominal centres. Minimum of one screw per location. Frame may also be installed by screw fixing the steel studs to the back of the timber frame during wall construction.
• Stops - nailed (50 x 3.2mm) at 200mm centres.
• Architrave - nailed (50 x 3.2mm) at 400mm centres.

Head Fixing (minimum):

• Single door - none required
• Paired door - single central fastener required

Wedging gap:

• 0-10mm

Frame materials available:

• EGZ - 1.6mm
• Cold rolled galvanized - 1.6mm
• Stainless Steel - 1.5mm

Fasteners:

• Frame screwed to boxed stud at 600mm nominal centres with self tapping screws.
• Steel studs may be riveted (steel pop rivets) or screwed (9g x 45mm self tapping) to the frame bracing straps.

Head Fixing (minimum):

• Single door - none required
• Paired door - single central fastener required

Wedging Gap:

• N/A

Frame materials available:

• Radiata pine or denser (standard thickness is 30mm)

Fasteners:

• Frame - Screwed (10g x 50mm self tapping) at 600mm centres and near hinges. Two screws per location.
• Stops - nailed (50 x 3.2mm) at 200mm centres.
• Architrave - nailed (50 x 3.2mm) at 400mm centres.

Head Fixing (minimum):

• Single door - none required
• Paired door - double central fastener required

Stud size:

• Ex 75x50mm minimum

Wedging gap:

• 0-10mm

Frame materials available:

• Radiata pine or denser (standard thickness is 30mm)

Fasteners:

• Frame - Screwed (10g x 50mm self tapping) at 600mm centres and near hinges. Two screws per location.
• Stops - nailed (50 x 3.2mm) at 200mm centres.
• Architrave - nailed (50 x 3.2mm) at 400mm centres.

Head Fixing (minimum):

• Single door - none required
• Paired door - double central fastener required

Stud size:

• Steel stud minimum 63mm, timber stud to match

Wedging gap:

• 0-10mm

Frame materials available:

• Hardwood of minimum density 580 kg/m3 (minimum thickness is 30mm)

Fasteners:

• Frame - Either nailed (75 x 3.2mm) or screwed (10g x 75mm) at 600mm centres nominal. Two fixings per location.
• Stops - nailed (50 x 3.2mm) at 200mm centres.
• Architrave - nailed (50 x 3.2mm) at 400mm centres.
• Pryda Jamb-fixa brackets Type JFB100 at 500mm centres may be used to fix profiles A & B to approved walls.

Head Fixing (minimum):

• Single door - none required
• Paired door - double central fastener required

Stud size:

• Ex 75 x 50 minimum.

Wedging gap:

• 0-10mm

Frame materials available:

• EGZ - 1.6mm
• Cold rolled galvanized - 1.6mm
• Stainless Steel - 1.5mm

Fasteners:

• Folded steel connection plates (as shown) to be supplied with frames.
• Hook onto frame bracing straps and nail or screw to timber studs.
• Frame connection plates either clouts (30 x 2.5mm gib clouts) or screw fixed.

Head Fixing (minimum):

• Single door - none required
• Paired door - single central fastener required

Stud size:

• Ex 100 x 50 minimum

Wedging gap:

• Not applicable

Insulation rating:

To obtain an insulation rating, the steel frame must be packed with either;

• Plasterboard (30 minutes)
• Ceramic fibre blanket (30 minutes)
• Cornice plaster (30 minutes)
• Grout (60 minutes)
• Pyropanel M4 mortar (60 minutes)

No frame packing equals no insulation rating (i.e. -/xx/-)

Frame materials available:

• EGZ - 1.6mm
• Cold rolled galvanized - 1.6mm
• Stainless Steel - 1.5mm

Fasteners:

• Frame screwed to stud through Gib Fyreline packing between stud and shims.
• Frame to be screw fixed (10g self tapping) at 600mm nominal centres. Two fasteners per location where applicable.

Head Fixing (minimum):

• Single door - none required
• Paired door - double central fastener required

Stud size:

• Ex 100 x 50 minimum

Wedging gap:

• 0-10mm

Insulation rating:

To obtain an insulation rating, the steel frame must be packed with either;

• Plasterboard (30 minutes)
• Ceramic fibre blanket (30 minutes)
• Cornice plaster (30 minutes)
• Grout (60 minutes)
• Pyropanel M4 mortar (60 minutes)

No frame packing equals no insulation rating (i.e. -/xx/-)

Frame materials available:
* EGZ - 1.6mm
* Cold rolled galvanized - 1.6mm
* Stainless Steel - 1.5mm

Fasteners:

• Frame to be screw fixed (10g self tapping through frame straps, timber packers and into timber stud. Standard is 4 No. per Jamb (Front section), 2 No. Per Jamb (Rear section)

Head Fixing (minimum):

• Single door - none required
• Paired door - 2 No. fasteners required (Front section only)

Stud size:

• Ex 100x50 minimum

Wedging gap:

• Not applicable

Insulation rating:

To obtain an insulation rating, the steel frame must be packed with either;

• Plasterboard (30 minutes)
• Ceramic fibre blanket (30 minutes)
• Cornice plaster (30 minutes)
• Grout (60 minutes)
• Pyropanel M4 mortar (60 minutes)

No frame packing equals no insulation rating (i.e. -/xx/-)

Frame materials available:

• EGZ - 1.6mm
• Cold rolled galvanized - 1.6mm

Fasteners:

• Frame to be screw fixed (10g self tapping) at 600mm nominal centres through frame straps and timber packers into timber stud.
• Standard is 4 no. per jamb (front section) and 2 no. per jamb (rear section)

Head Fixing (minimum):

• Single door - none required
• Paired door - 2 no. fasteners required (front section only)

Stud size:

• Ex 100 x 50 minimum

Wedging gap:

• 0-10mm

Insulation rating:

To obtain an insulation rating, all voids in the steel frame and wedging gaps must be packed with either;

• Plasterboard (30 minutes)
• Ceramic fibre blanket, 96 kg/m3 min. (30 minutes)
• Mineral wool blanket, 96 kg/m3 min. (30 minutes)

No frame packing equals no insulation rating (i.e. -/xx/-)

Frame materials available:

• EGZ - 1.6mm
• Cold rolled galvanized - 1.6mm
• Stainless Steel - 1.5mm (Must be fully grouted frame VP90-120)

Fasteners:

• Jamb fixing at 600mm centres minimum
• Expansion anchors eg. M10 countersunk 'Ramset' Dynabolts
• M12 countersunk masonry screwbolts

Head Fixing (minimum):

• Single door - none required
• Paired door - single central fastener required

Wedging Gap:

• 0-15mm

Insulation rating:

To obtain an insulation rating, the steel frame must be packed with either;

• Plasterboard (30 minutes)
• Ceramic fibre blanket (30 minutes)
• Cornice plaster (30 minutes)
• Grout (60 minutes)
• Pyropanel M4 mortar (60 minutes)

No frame packing equals no insulation rating (i.e. -/xx/-)

Frame materials available:

• Hardwood of minimum density 580 kg/m3 (minimum thickness is 30mm)

Fasteners:

• Frame - Screwed (10g self tapping) at 600mm centres nominal. Minimum of one screw per location. Frames may also be installed by screw fixing the steel studs to the back of the timber frame during wall construction.
• Stops - nailed (50 x 3.2mm) at 200mm centres.
• Architrave - nailed (50 x 3.2mm) at 400mm centres.

Head Fixing (minimum):

• Single door - none required
• Paired door - double central fastener required

Stud size:

• 65 x 34mm minimum of 0.55 MSG gauge.

Wedging gap:

• 0-10mm

Frame materials available:

• Hardwood timber of minimum density 580 kg/m3 (minimum thickness is 30mm)

Fasteners:

• Frame - Screwed (10g self tapping) at 600mm centres nominal. Minimum of one screw per location. Frames may also be installed by screw fixing the steel studs to the back of the timber frame during wall construction.
• Stops - nailed (50 x 3.2mm) at 200mm centres.
• Architrave - nailed (50 x 3.2mm) at 400mm centres.

Head Fixing (minimum):

• Single door - none required
• Paired door - double central fastener required

Stud size:

• 65 x 34mm minimum of 0.55 MSG gauge.

Wedging gap:

• 0-10mm

Frame materials available:

• EGZ - 1.6mm
• Cold rolled galvanized - 1.6mm
• Stainless Steel - 1.5mm

Fasteners:

• Frame screwed to boxed stud at 600mm centres nominal with self tapping screws.
• Steel studs may be riveted (steel pop rivets) or screwed (10g self tapping) to the frame bracing straps at 600mm centres nominal.

Head Fixing (minimum):

• Single door - none required
• Paired door - double central fastener required

Stud size:

• 65 x 34mm minimum of 0.55 SMG gauge

Wedging gap:

• Not applicable

Insulation rating:

To obtain an insulation rating, the steel frame must be packed with either;

• Plasterboard (30 minutes)
• Ceramic fibre blanket (30 minutes)
• Cornice plaster (30 minutes)
• Grout (60 minutes)
• Pyropanel M4 mortar (60 minutes)

No frame packing equals no insulation rating (i.e. -/xx/-)

Frame materials available:

• Hardwood timber - Min density 580kg/m≥ (minimum thickness is 30mm)

Fasteners:

• Frame - Screwed (10g self tapping) at 600mm centres nominal. Two screws per location. 
• Stops - nailed (50 x 3.2mm) at 200mm centres.
• Architrave - nailed (50 x 3.2mm) at 400mm centres.

Head Fixing (minimum):

• Single door - none required

Wall type:

• Korok panels with 13 mm FRR plasterboard on furring channels to one side. Trim opening to be framed with nom. 45 mm timber.

Wedging gap:

• 0-10mm

Frame materials available:

• EGZ - 1.6mm
• Cold rolled galvanized - 1.6mm

Fasteners:

• Jamb fixing 6 sets (i.e. 12 per jamb)
• 10 x 75mm Gauge self tapping screws

Head Fixing (minimum):

• Single door - none required
• Paired door - 1 set

Wedging gap:

• 0 - 15mm

Fire rating for unlined Speedpanel / Korok walls:

• 51 mm wall: Max. FRR -/60/30
• 64 mm wall: Max. FRR -/90/30
• 78 mm wall: Max. FRR -/120/30

Integrity rating can be increased by 30 minutes by lining the wall one or both sides, up to a max. of 120 minutes.

Frame has to be filled with plasterboard, ceramic fibre blanket or grout to achieve 30 minute insulation rating.

Frame materials available:

• EGZ - 1.6mm
• Cold rolled galvanized - 1.6mm

Fasteners:

• Jamb fixing 6 sets (i.e. 12 per jamb)
• 10g x 75mm self tapping screws

Head Fixing (minimum):

• Single door - none required
• Paired door - 1 set

Wedging gap:

• 0 - 15mm

Fire rating for unlined Speedpanel / Korok walls:

• 51 mm wall: Max. FRR -/60/30
• 64 mm wall: Max. FRR -/90/30
• 78 mm wall: Max. FRR -/120/30

Integrity rating can be increased by 30 minutes by lining the wall one or both sides, up to a max. of 120 minutes.

Frame has to be filled with plasterboard, ceramic fibre blanket or grout to achieve 30 minute insulation rating.

Frame materials available:

• EGZ - 1.6mm
• Cold rolled galvanized - 1.6mm

Fasteners:

• Jamb fixing 6 sets (i.e. 12 per jamb)
• 10g x 75mm self tapping screws

Head Fixing (minimum):

• Single door - none required
• Paired door - 1 set

Wedging gap:

• 0 - 15mm

Fire rating for unlined Speedpanel / Korok walls:

• 51 mm wall: Max. FRR -/60/30
• 64 mm wall: Max. FRR -/90/30
• 78 mm wall: Max. FRR -/120/30

Integrity rating can be increased by 30 minutes by lining the wall one or both sides, up to a max. of 120 minutes.

Frame has to be filled with plasterboard, ceramic fibre blanket or grout to achieve 30 minute insulation rating.

Frame materials available:

• EGZ - 1.6mm
• Cold rolled galvanized - 1.6mm

Fasteners:

• Jamb fixing 6 sets (i.e. 12 per jamb)
• 10g x 75mm self tapping screws

Head Fixing (minimum):

• Single door - none required
• Paired door - 1 set

Wedging gap:

• 0 - 15mm

Fire rating for unlined Speedpanel / Korok walls:

• 51 mm wall: Max. FRR -/60/30
• 64 mm wall: Max. FRR -/90/30
• 78 mm wall: Max. FRR -/120/30

Integrity rating can be increased by 30 minutes by lining the wall one or both sides, up to a max. of 120 minutes.

Frame has to be filled with plasterboard, ceramic fibre blanket or grout to achieve 30 minute insulation rating.

Frame materials available:

• EGZ - 1.6mm
• Cold rolled galvanized - 1.6mm

Fasteners:

• Jamb fixing 6 sets (i.e. 12 per jamb)
• 10g x 75mm self tapping screws

Head Fixing (minimum):

• Single door - none required
• Paired door - 1 set

Wedging gap:

• 0 - 15mm

Fire rating for unlined Speedpanel / Korok walls:

• 51 mm wall: Max. FRR -/60/30
• 64 mm wall: Max. FRR -/90/30
• 78 mm wall: Max. FRR -/120/30

Integrity rating can be increased by 30 minutes by lining the wall one or both sides, up to a max. of 120 minutes.

Frame has to be filled with plasterboard, ceramic fibre blanket or grout to achieve 30 minute insulation rating.

Frame materials available:

• EGZ - 1.6mm
• Cold rolled galvanized - 1.6mm

Fasteners:

• Jamb fixing 6 sets (i.e. 12 per jamb)
• 10g x 75mm self tapping screws

Head Fixing (minimum):

• Single door - none required
• Paired door - 1 set

Wedging gap:

• 0 - 15mm

Fire rating for unlined Speedpanel / Korok walls:

• 51 mm wall: Max. FRR -/60/30
• 64 mm wall: Max. FRR -/90/30
• 78 mm wall: Max. FRR -/120/30

Integrity rating can be increased by 30 minutes by lining the wall one or both sides, up to a max. of 120 minutes.

Frame has to be filled with plasterboard, ceramic fibre blanket or grout to achieve 30 minute insulation rating.

Frame materials available:

• Hardwood of minimum density 580 kg/m³ (minimum thickness is 30mm)

Fasteners:

• Frame - Either nailed (75 x 3.2mm) or screwed (10g x 75mm) at 600mm centres. Two fixings per location.
• Stops - nailed (50 x 3.2mm) at 200mm centres.
• Architrave - nailed (50 x 3.2mm) at 400mm centres.

Head Fixing (minimum):

• Single door - none required
• Paired door - double central fastener required

Stud size:

• Ex 75 x 50 minimum.

Wedging gap:

• 0-15mm

Frame materials available:

• EGZ - 1.6mm
• Cold rolled galvanized - 1.6mm
• Stainless Steel - 1.5mm

Fasteners:

• Framing stud No.1 screwed to jamb.
• Connection to stud No.2 via rebated nail on plates. One fastener per location except at bottom where two fasteners are required.
• Frame to be screw fixed (10g self tapping) at 600mm nominal centres. Two fasteners per location where applicable.

Head Fixing (minimum):

• Single door - none required
• Paired door - double central fastener required

Stud size:

• Ex 100x50 minimum

Wedging gap:

• Not applicable

Insulation rating:

To obtain an insulation rating, the steel frame must be packed with either;

• Plasterboard (30 minutes)
• Ceramic fibre blanket (30 minutes)
• Cornice plaster (30 minutes)
• Grout (60 minutes)
• Pyropanel M4 mortar (60 minutes)

No frame packing equals no insulation rating (i.e. -/xx/-)

Frame materials available:

• EGZ - 1.6mm
• Cold rolled galvanized - 1.6mm
• Stainless Steel - 1.5mm

Fasteners:

• Frames may be screwed directly to studs either through the stud and into the frame bracing straps or through the frame into the timber stud at 600mm centres nominal.
• Frame to be screw fixed (10g self tapping) at 600mm centres nominal. Two fasteners per location where applicable.

Head Fixing (minimum):

• Single door - none required
• Paired door - double central fastener required

Stud size:

• Ex 100 x 50 minimum

Wedging gap:

• Not applicable

Insulation rating:

To obtain an insulation rating, the steel frame must be packed with either;

• Plasterboard (30 minutes)
• Ceramic fibre blanket (30 minutes)
• Cornice plaster (30 minutes)
• Grout (60 minutes)
• Pyropanel M4 mortar (60 minutes)

No frame packing equals no insulation rating (i.e. -/xx/-)

Frame materials available:

• Cold rolled galvanized - 1.6mm packed with pla board

Fasteners:

• Frame to be screw fixed with 10 x 75mm gauge screws at 600mm centres nominal.

Head Fixing (minimum):

• Single door - non required
• Paired door - double central fastener required

Stud Size

• Ex 100 x 50 minimum

Wedging gap:

0 - 10mm

Insulation rating:

To obtain an insulation rating, the steel frame must be packed with either;

• Plasterboard (30 minutes)
• Ceramic fibre blanket (30 minutes)
• Cornice plaster (30 minutes)
• Grout (60 minutes)
• Pyropanel M4 mortar (60 minutes)

No frame packing equals no insulation rating (i.e. -/xx/-)

Gib Universal wall systems - One way FRR only

Please refer to Gib Fire Rated Systems manual for thickness and number of lining boards.

Frame materials available:

• Cold rolled galvanized - 1.6mm

Fasteners:

• Frame screwed to stud
• Frame to be screw fixed (10g self tapping) at 600 mm nominal centres. Two fasteners per location where applicable

Head Fixing (minimum):

• Single door - none required
• Pair door - double central fastener required

Stud size:

• Ex 100 x 50 minimum

Wedging gap:

• 0-10 mm

Insulation rating:

To obtain an insulation rating, the steel frame must be packed with either;

• Plasterboard (30 minutes)
• Ceramic fibre blanket (30 minutes)
• Cornice plaster (30 minutes)
• Grout (60 minutes)
• Pyropanel M4 mortar (60 minutes)

No frame packing equals no insulation rating (i.e. -/xx/-)

Frame materials available:

• Hardwood of minimum density 580 kg/m³ (minimum thickness is 30mm)

Fasteners:

• Frame - M8 or M10 'Ramset' Dynabolts at 600mm centres nominal. Fixings on or near centre of frame jamb.
• Stops - nailed (50 x 3.2mm) at 200mm centres.
• Architrave -nailed (50 x 3.2mm) at 400mm centres.

Head Fixing (minimum):

• Single door - none required
• Paired door - single central fastener required

Wedging gap:

• 0-15mm

Frame materials available:

• EGZ - 1.6mm
• Cold rolled galvanized - 1.6mm
• Stainless Steel - 1.5mm

Fasteners:

• Frame screwed to boxed stud at 600mm centres nominal with self tapping screws.
• Steel studs may be riveted (steel pop rivets) or screwed (10g self tapping) to the frame bracing straps at 600mm centres nominal.

Head Fixing (minimum):

• Single door - none required
• Paired door - double central fastener required

Stud size:

• 65 x 34mm minimum of 0.55 SMG gauge

Wedging gap:

• Not applicable

Insulation rating:

To obtain an insulation rating, the steel frame must be packed with either;

• Plasterboard (30 minutes)
• Ceramic fibre blanket (30 minutes)
• Cornice plaster (30 minutes)
• Grout (60 minutes)
• Pyropanel M4 mortar (60 minutes)

No frame packing equals no insulation rating (i.e. -/xx/-)

Frame materials available:

• EGZ - 1.6mm
• Cold rolled galvanized - 1.6mm

Fasteners:

• Frame screwed to stud through Gib Fyreline packing between stud and shims.
• Frame to be screw fixed (10g x 50mm self tapping) at 600mm nominal centres. Two fasteners per location where applicable.

Head Fixing (minimum):

• Single door - none required
• Paired door - single central fastener required

Stud size:

• 92 x 34mm minimum of 0.55 SMG gauge

Wedging gap:

• 0-10mm

Insulation rating:

To obtain an insulation rating, the steel frame must be packed with either;

• Plasterboard (30 minutes)
• Ceramic fibre blanket (30 minutes)
• Cornice plaster (30 minutes)
• Grout (60 minutes)
• Pyropanel M4 mortar (60 minutes)

No frame packing equals no insulation rating (i.e. -/xx/-)

Frame materials available:

• Hardwood of minimum density 580 kg/m³ (minimum thickness is 42mm)

Fasteners:

• Frame - Either nailed (75 x 3.2mm) or screwed (10g x 75mm) at 600mm centres nominal. Two fixings per location.
• Stops - nailed (50 x 3.2mm) at 200mm centres.
• Architrave - nailed (50 x 3.2mm) at 400mm centres.
• Pryda Jamb-fixa brackets Type JFB100 at 500mm centres may be used to fix profiles A & B to approved walls.

Stud size:

• Ex 75x50 minimum.

Wedging gap:

• 0-10mm

Frame materials available:

• Radiata pine or denser (standard thickness is 30mm)

Fasteners:

• Frame - M8 or M10 'Ramset' Dynabolts at 600mm centres and near hinges. Fixings on or near centre of frame jamb.
• Stops - nailed (50 x 3.2mm) at 200mm centres.
• Architrave - nailed (50 x 3.2mm) at 400mm centres.

Head Fixing (minimum):

• Single door - none required
• Paired door - single central fastener required

Wedging gap:

• 0-15mm

Frame materials available:

• EGZ - 1.6mm
• Cold rolled galvanized - 1.6mm
• Stainless Steel - 1.5mm (VP30-60DA only)

Fasteners:

• Framing stud No.1 screwed to jamb.
• Connection to stud No.2 via rebated nail on plates. One fastener per location except at bottom where two fasteners are required.
• Frame to be screw fixed (10g self tapping) at 600mm centres nominal. Two fasteners per location where applicable.

Head Fixing (minimum):

• Single door - none required
• Paired door - double central fastener required

Stud size:

• Ex 100x50mm minimum

Wedging gap:

• Not applicable

Insulation rating:

To obtain an insulation rating, the steel frame must be packed with either;

• Plasterboard (30 minutes)
• Ceramic fibre blanket (30 minutes)
• Cornice plaster (30 minutes)
• Grout (60 minutes)
• Pyropanel M4 mortar (60 minutes)

No frame packing equals no insulation rating (i.e. -/xx/-)

Frame materials available:

• EGZ - 1.6mm
• Cold rolled galvanized - 1.6mm
• Stainless Steel - 1.5mm (VP30-60 ONLY)

Fasteners:

• Frames may be screwed directly to studs either through the stud and into the frame bracing straps or through the frame into the timber stud at 600mm centres nominal.
• Frame to be screw fixed (10g self tapping) at 600mm centres nominal. Two fasteners per location where applicable.

Head Fixing (minimum):

• Single door - none required
• Paired door - double central fastener required

Stud size:

• Ex 100x50mm minimum

Wedging gap:

• Not applicable

Insulation rating:

To obtain an insulation rating, the steel frame must be packed with either;

• Plasterboard (30 minutes)
• Ceramic fibre blanket (30 minutes)
• Cornice plaster (30 minutes)
• Grout (60 minutes)
• Pyropanel M4 mortar (60 minutes)

No frame packing equals no insulation rating (i.e. -/xx/-)

Frame materials available:

• EGZ - 1.6mm
• Cold rolled galvanized - 1.6mm
• Stainless Steel - 1.5mm (VP120DA Must be fully grouted frame)

Fasteners:

• Jamb fixing at 600mm centres nominal
• Expansion anchors eg. M10 countersunk 'Ramset' Dynabolts
• M12 countersunk masonry screwbolts

Head Fixing (minimum):

• Single door - none required
• Paired door - single central fastener required

Wedging Gap:

• 0-15mm

Insulation rating:

To obtain an insulation rating, the steel frame must be packed with either;

• Plasterboard (30 minutes)
• Ceramic fibre blanket (30 minutes)
• Cornice plaster (30 minutes)
• Grout (60 minutes)
• Pyropanel M4 mortar (60 minutes)

No frame packing equals no insulation rating (i.e. -/xx/-)

Frame materials available:

• EGZ - 1.6mm
• Cold rolled galvanized - 1.6mm
• Stainless Steel - 1.5mm (VP30 and 60DA ONLY)

Fasteners:

• Frame screwed to boxed stud at 600mm centres nominal with self tapping screws.
• Steel studs may be riveted (steel pop rivets) or screwed (10g self tapping) to the frame bracing straps at 600 centres nominal.

Head Fixing (minimum):

• Single door - none required
• Paired door - single central fastener required

Stud size:

• 65 x 34mm minimum of 0.55 SMG gauge

Wedging gap:

• Not applicable

Insulation rating:

To obtain an insulation rating, the steel frame must be packed with either;

• Plasterboard (30 minutes)
• Ceramic fibre blanket (30 minutes)
• Cornice plaster (30 minutes)
• Grout (60 minutes)
• Pyropanel M4 mortar (60 minutes)

No frame packing equals no insulation rating (i.e. -/xx/-)

Frame materials available:

• Radiata pine or denser, minimum 30mm thick (standard thicknesses are 30mm or 42mm)

Fasteners:

• Frame - either nailed (75x3.2mm) or screwed (10gx75mm) at 600mm centres. Two nails or screws per location.
• Stops - nailed (50x3.2mm) at 200mm centres.
• Architrave - nailed (50x3.2mm) at 400mm centres.
• Pryda Jamb-fixa brackets Type JBF100 at 500mm centres.

Stud size:

• ex 75x50mm minimum

Wedging gap:

• 0-6mm

Frame materials available:

• EGZ - 1.6mm
• Cold rolled galvanised - 1.6mm

Fasteners:

• Folded steel connection plates (as shown) to be supplied with frames.
• Hook onto frame bracing straps and nail or screw to timber studs.
• Frame connection plates either clouts (30 x 2.5mm gib clouts) or screw fixed.

Head Fixing (minimum):

• Single door - none required
• Paired door - single central fastener required

Stud size:

• Ex 75x50 minimum

Wedging Gap:

• Not applicable

Frame materials available:

• EGZ - 1.6mm
• Cold rolled galvanized - 1.6mm

Fasteners:

• Countersunk anchor method - Jamb fixings at 600mm centres nominal: M10 expansion anchors eg Dynabolt D10102F (as shown) or M12 masonry screwbolts. The length of bolts MUST be confirmed on site to suit the frame openings formed.

Head Fixing (minimum):

• Single door - none required.
• Paired door - single central fastener required.

Wedging Gap:

• 0-15mm

Frame materials available:

• Radiata pine or denser, minimum 30mm thick (standard thicknesses are 30mm or 42mm)

Fasteners:

• Frame - either nailed (75x3.2mm) or screwed (10gx75mm) at 600mm centres. Two nails or screws per location.
• Stops - nailed (50x3.2mm) at 200mm centres.
• Architrave - nailed (50x3.2mm) at 400mm centres.
• Pryda Jamb-fixa brackets Type JBF100 at 500mm centres.

Head Fixing (minimum):

• Single door - none required
• Paired door - double central fastener required

Stud size:

• Steel stud minimum 63mm, timber stud to match

Wedging gap:

• 0-6mm

Frame materials available:

• Hardwood timber - Min. density 580kg/m≥ (minimum thickness is 30mm)

Fasteners:

• Frame - Either nailed (75 x 3.2mm) or screwed (10g x 75mm) at 600mm centres nominal. Two fixings per location.
• Stops - nailed (50 x 3.2mm) at 200mm centres.
• Architrave - nailed (50 x 3.2mm) at 400mm centres.
• Pryda Jamb-fixa brackets Type JFB100 at 500mm centres may be used to fix profiles A & B to approved walls.

Head Fixing (minimum):

• Single door - none required
• Paired door - single central fastener required

Stud size:

• Ex 100 x 50 minimum.

Wedging gap:

• 0-10mm

Frame materials available:

• EGZ - 1.6mm
• Cold rolled galvanized - 1.6mm
• Stainless Steel - 1.5mm

Fasteners:

• Folded steel connection plates (as shown) to be supplied with frames.
• Hook onto frame bracing straps and nail or screw to timber studs.
• Frame connection plates either clouts (30 x 2.5mm gib clouts) or screw fixed.

Head Fixing (minimum):

• Single door - none required
• Paired door - single central fastener required

Stud size:

• Ex 100 x 50 minimum

Wedging gap:

• Not applicable

Insulation rating:

To obtain an insulation rating, the steel frame must be packed with either;

• Plasterboard (30 minutes)
• Ceramic fibre blanket (30 minutes)
• Cornice plaster (30 minutes)
• Grout (60 minutes)
• Pyropanel M4 mortar (60 minutes)

No frame packing equals no insulation rating (i.e. -/xx/-)

Frame materials available:

• EGZ - 1.6mm
• Cold rolled galvanized - 1.6mm
• Stainless Steel - 1.5mm

Fasteners:

• Frame screwed to stud through Gib Fyreline packing between stud and shims.
• Frame to be screw fixed (10g self tapping) at 600mm nominal centres. Two fasteners per location where applicable.

Head Fixing (minimum):

• Single door - none required
• Paired door - double central fastener required

Stud size:

• Ex 100 x 50 minimum

Wedging gap:

• 0-10mm

Insulation rating:

To obtain an insulation rating, the steel frame must be packed with either;

• Plasterboard (30 minutes)
• Ceramic fibre blanket (30 minutes)
• Cornice plaster (30 minutes)
• Grout (60 minutes)
• Pyropanel M4 mortar (60 minutes)

No frame packing equals no insulation rating (i.e. -/xx/-)

Frame materials available:
* EGZ - 1.6mm
* Cold rolled galvanized - 1.6mm
* Stainless Steel - 1.5mm

Fasteners:

• Frame to be screw fixed (10g self tapping through frame straps, timber packers and into timber stud. Standard is 4 No. per Jamb (Front section), 2 No. Per Jamb (Rear section)

Head Fixing (minimum):

• Single door - none required
• Paired door - 2 No. fasteners required (Front section only)

Stud size:

• Ex 100x50 minimum

Wedging gap:

• Not applicable

Insulation rating:

To obtain an insulation rating, the steel frame must be packed with either;

• Plasterboard (30 minutes)
• Ceramic fibre blanket (30 minutes)
• Cornice plaster (30 minutes)
• Grout (60 minutes)
• Pyropanel M4 mortar (60 minutes)

No frame packing equals no insulation rating (i.e. -/xx/-)

Frame materials available:

• EGZ - 1.6mm
• Cold rolled galvanized - 1.6mm

Fasteners:

• Frame to be screw fixed (10g self tapping) at 600mm nominal centres through frame straps and timber packers into timber stud.
• Standard is 4 no. per jamb (front section) and 2 no. per jamb (rear section)

Head Fixing (minimum):

• Single door - none required
• Paired door - 2 no. fasteners required (front section only)

Stud size:

• Ex 100 x 50 minimum

Wedging gap:

• 0-10mm

Insulation rating:

To obtain an insulation rating, all voids in the steel frame and wedging gaps must be packed with either;

• Plasterboard (30 minutes)
• Ceramic fibre blanket, 96 kg/m3 min. (30 minutes)
• Mineral wool blanket, 96 kg/m3 min. (30 minutes)

No frame packing equals no insulation rating (i.e. -/xx/-)

Frame materials available:

• EGZ - 1.6mm
• Cold rolled galvanized - 1.6mm
• Stainless Steel - 1.5mm (Must be fully grouted frame VP90-120)

Fasteners:

• Jamb fixing at 600mm centres minimum
• Expansion anchors eg. M10 countersunk 'Ramset' Dynabolts
• M12 countersunk masonry screwbolts

Head Fixing (minimum):

• Single door - none required
• Paired door - single central fastener required

Wedging Gap:

• 0-15mm

Insulation rating:

To obtain an insulation rating, the steel frame must be packed with either;

• Plasterboard (30 minutes)
• Ceramic fibre blanket (30 minutes)
• Cornice plaster (30 minutes)
• Grout (60 minutes)
• Pyropanel M4 mortar (60 minutes)

No frame packing equals no insulation rating (i.e. -/xx/-)

Frame materials available:

• Hardwood timber - Min density 580kg/m≥ (minimum thickness is 30mm)

Fasteners:

• Frame - Screwed (10g self tapping) at 600mm centres nominal. Two screws per location. 
• Stops - nailed (50 x 3.2mm) at 200mm centres.
• Architrave - nailed (50 x 3.2mm) at 400mm centres.

Head Fixing (minimum):

• Single door - none required

Wall type:

• Korok panels with 13 mm FRR plasterboard on furring channels to one side. Trim opening to be framed with nom. 45 mm timber.

Wedging gap:

• 0-10mm

Frame materials available:

• EGZ - 1.6mm
• Cold rolled galvanized - 1.6mm

Fasteners:

• Jamb fixing 6 sets (i.e. 12 per jamb)
• 10g x 75mm self tapping screws

Head Fixing (minimum):

• Single door - none required
• Paired door - 1 set

Wedging gap:

• 0 - 15mm

Fire rating for unlined Speedpanel / Korok walls:

• 51 mm wall: Max. FRR -/60/30
• 64 mm wall: Max. FRR -/90/30
• 78 mm wall: Max. FRR -/120/30

Integrity rating can be increased by 30 minutes by lining the wall one or both sides, up to a max. of 120 minutes.

Frame has to be filled with plasterboard, ceramic fibre blanket or grout to achieve 30 minute insulation rating.

Frame materials available:

• EGZ - 1.6mm
• Cold rolled galvanized - 1.6mm

Fasteners:

• Jamb fixing 6 sets (i.e. 12 per jamb)
• 10g x 75mm self tapping screws

Head Fixing (minimum):

• Single door - none required
• Paired door - 1 set

Wedging gap:

• 0 - 15mm

Fire rating for unlined Speedpanel / Korok walls:

• 51 mm wall: Max. FRR -/60/30
• 64 mm wall: Max. FRR -/90/30
• 78 mm wall: Max. FRR -/120/30

Integrity rating can be increased by 30 minutes by lining the wall one or both sides, up to a max. of 120 minutes.

Frame has to be filled with plasterboard, ceramic fibre blanket or grout to achieve 30 minute insulation rating.

Frame materials available:

• EGZ - 1.6mm
• Cold rolled galvanized - 1.6mm

Fasteners:

• Jamb fixing 6 sets (i.e. 12 per jamb)
• 10g x 75mm self tapping screws

Head Fixing (minimum):

• Single door - none required
• Paired door - 1 set

Wedging gap:

• 0 - 15mm

Fire rating for unlined Speedpanel / Korok walls:

• 51 mm wall: Max. FRR -/60/30
• 64 mm wall: Max. FRR -/90/30
• 78 mm wall: Max. FRR -/120/30

Integrity rating can be increased by 30 minutes by lining the wall one or both sides, up to a max. of 120 minutes.

Frame has to be filled with plasterboard, ceramic fibre blanket or grout to achieve 30 minute insulation rating.

Frame materials available:

• EGZ - 1.6mm
• Cold rolled galvanized - 1.6mm

Fasteners:

• Jamb fixing 6 sets (i.e. 12 per jamb)
• 10g x 75mm self tapping screws

Head Fixing (minimum):

• Single door - none required
• Paired door - 1 set

Wedging gap:

• 0 - 15mm

Fire rating for unlined Speedpanel / Korok walls:

• 51 mm wall: Max. FRR -/60/30
• 64 mm wall: Max. FRR -/90/30
• 78 mm wall: Max. FRR -/120/30

Integrity rating can be increased by 30 minutes by lining the wall one or both sides, up to a max. of 120 minutes.

Frame has to be filled with plasterboard, ceramic fibre blanket or grout to achieve 30 minute insulation rating.

Frame materials available:

• EGZ - 1.6mm
• Cold rolled galvanized - 1.6mm

Fasteners:

• Jamb fixing 6 sets (i.e. 12 per jamb)
• 10g x 75mm self tapping screws

Head Fixing (minimum):

• Single door - none required
• Paired door - 1 set

Wedging gap:

• 0 - 15mm

Fire rating for unlined Speedpanel / Korok walls:

• 51 mm wall: Max. FRR -/60/30
• 64 mm wall: Max. FRR -/90/30
• 78 mm wall: Max. FRR -/120/30

Integrity rating can be increased by 30 minutes by lining the wall one or both sides, up to a max. of 120 minutes.

Frame has to be filled with plasterboard, ceramic fibre blanket or grout to achieve 30 minute insulation rating.

Note: This installation method is only applicable to 78 mm Korok walls

Frame materials available:

• EGZ - 1.6mm
• Cold rolled galvanized - 1.6mm

Fasteners:

• Jamb fixing 6 sets (i.e. 12 per jamb)
• 10 x 75mm Gauge self tapping screws

Head Fixing (minimum):

• Single door - none required
• Paired door - 1 set

Wedging gap:

• 0 - 15mm

Fire rating for unlined Speedpanel / Korok walls:

• 78 mm wall: Max. FRR -/120/30

Frame has to be filled with plasterboard, ceramic fibre blanket or grout to achieve 30 minute insulation rating.

Frame materials available:

• Hardwood timber - Min. density 580kg/m≥ (minimum thickness is 30mm)

Fasteners:

• Frame - Either nailed (75 x 3.2mm) or screwed (10g x 75mm) at 600mm centres nominal. Two fixings per location.
• Stops - nailed (50 x 3.2mm) at 200mm centres.
• Architrave - nailed (50 x 3.2mm) at 400mm centres.
• Pryda Jamb-fixa brackets Type JFB100 at 500mm centres may be used to fix profiles A & B to approved walls.

Head Fixing (minimum):

• Single door - none required
• Paired door - single central fastener required

Stud size:

• Ex 100 x 50 minimum.

Wedging gap:

• 0-10mm

Frame materials available:

• EGZ - 1.6mm
• Cold rolled galvanized - 1.6mm
• Stainless Steel - 1.5mm

Fasteners:

• Framing stud No.1 screwed to jamb.
• Connection to stud No.2 via rebated nail on plates. One fastener per location except at bottom where two fasteners are required.
• Frame to be screw fixed (10g self tapping) at 600mm nominal centres. Two fasteners per location where applicable.

Head Fixing (minimum):

• Single door - none required
• Paired door - double central fastener required

Stud size:

• Ex 100x50 minimum

Wedging gap:

• Not applicable

Insulation rating:

To obtain an insulation rating, the steel frame must be packed with either;

• Plasterboard (30 minutes)
• Ceramic fibre blanket (30 minutes)
• Cornice plaster (30 minutes)
• Grout (60 minutes)
• Pyropanel M4 mortar (60 minutes)

No frame packing equals no insulation rating (i.e. -/xx/-)

Frame materials available:

• EGZ - 1.6mm
• Cold rolled galvanized - 1.6mm
• Stainless Steel - 1.5mm

Fasteners:

• Frames may be screwed directly to studs either through the stud and into the frame bracing straps or through the frame into the timber stud at 600mm centres nominal.
• Frame to be screw fixed (10g self tapping) at 600mm centres nominal. Two fasteners per location where applicable.

Head Fixing (minimum):

• Single door - none required
• Paired door - double central fastener required

Stud size:

• Ex 100 x 50 minimum

Wedging gap:

• Not applicable

Insulation rating:

To obtain an insulation rating, the steel frame must be packed with either;

• Plasterboard (30 minutes)
• Ceramic fibre blanket (30 minutes)
• Cornice plaster (30 minutes)
• Grout (60 minutes)
• Pyropanel M4 mortar (60 minutes)

No frame packing equals no insulation rating (i.e. -/xx/-)

Frame materials available:

• Cold rolled galvanized - 1.6mm packed with pla board

Fasteners:

• Frame to be screw fixed with 10 x 75mm gauge screws at 600mm centres nominal.

Head Fixing (minimum):

• Single door - non required
• Paired door - double central fastener required

Stud Size

• Ex 100 x 50 minimum

Wedging gap:

0 - 10mm

Insulation rating:

To obtain an insulation rating, the steel frame must be packed with either;

• Plasterboard (30 minutes)
• Ceramic fibre blanket (30 minutes)
• Cornice plaster (30 minutes)
• Grout (60 minutes)
• Pyropanel M4 mortar (60 minutes)

No frame packing equals no insulation rating (i.e. -/xx/-)

Gib Universal wall systems - One way FRR only

Please refer to Gib Fire Rated Systems manual for thickness and number of lining boards.

Frame materials available:

• Cold rolled galvanized - 1.6mm

Fasteners:

• Frame screwed to stud
• Frame to be screw fixed (10g self tapping) at 600 mm nominal centres. Two fasteners per location where applicable

Head Fixing (minimum):

• Single door - none required
• Pair door - double central fastener required

Stud size:

• Ex 100 x 50 minimum

Wedging gap:

• 0-10 mm

Insulation rating:

To obtain an insulation rating, the steel frame must be packed with either;

• Plasterboard (30 minutes)
• Ceramic fibre blanket (30 minutes)
• Cornice plaster (30 minutes)
• Grout (60 minutes)
• Pyropanel M4 mortar (60 minutes)

No frame packing equals no insulation rating (i.e. -/xx/-)