Pacific Hollow Core Door Set Installation

Frame materials available:

• Timber (any species), Pine clear standard

Fasteners:

• Frame - Either nailed (75 x 3.2mm) or screwed (10g x 75mm) at 600mm centres. Two fixings per location.
• Stops - nailed (50 x 3.2mm) at 200mm centres.
• Architrave - nailed (50 x 3.2mm) at 400mm centres.
• Pryda Jamb-fixa brackets Type JFB100 at 500mm centres may be used.

Head Fixing (minimum):

• Single door - none required
• Paired door - Double central fastener required

Wedging gap:

• 0-10mm

Frame materials available:

• Timber (any species), Pine clear standard

Fasteners:

• Frame - Either nailed (75 x 3.2mm) or screwed (10g x 75mm) at 600mm centres. Two fixings per location.
• Stops - nailed (50 x 3.2mm) at 200mm centres.
• Architrave - nailed (50 x 3.2mm) at 400mm centres.
• Pryda Jamb-fixa brackets Type JFB100 at 500mm centres may be used.

Head Fixing (minimum):

• Single door - none required
• Paired door - single central fastener required

Wedging gap:

• 0-10mm

Frame materials available:

• EGZ - 1.6mm
• Cold rolled galvanized - 1.6mm
• Stainless Steel - 1.5mm

Fasteners:

• Framing stud No.1 screwed to jamb.
• Connection to stud No.2 via rebated nail on plates. One fastener per location except at bottom where two fasteners are required.
• Frame to be screw fixed (10g x 50mm self tapping) at 600mm nominal centres. Two fasteners per location where applicable.

Head Fixing (minimum):

• Single door - none required
• Paired door - single central fastener required

Wedging Gap:

• N/A

Frame materials available:

• EGZ - 1.6mm
• Cold rolled galvanized - 1.6mm
• Stainless Steel - 1.5mm

Fasteners:

• Frames may be screwed directly to studs either through the stud and into the frame bracing straps or through the frame into the timber stud at 600mm nominal centres.
• Frame to be screw fixed (10g x 50mm self tapping) at 600mm min. centres. Two fasteners per location where applicable to each strap.

Head Fixing (minimum):

• Single door - none required
• Paired door - single central fastener required

Wedging Gap:

• 0-15mm

Frame materials available:

• EGZ - 1.6mm
• Cold rolled galvanized - 1.6mm
• Stainless Steel - 1.5mm

Fasteners:

• Frame to be screw fixed (8g x 50mm self tapping) through frame straps, timber packers and into timber stud. Standard is 4 No. per Jamb (Front section), 2 No. Per Jamb (Rear section)

Head Fixing (minimum):

• Single door - none required
• Paired door - 2 No. fastener required (Front section only)

Wedging Gap:

• 10mm

Frame materials available:

• EGZ - 1.6mm
• Cold rolled galvanized - 1.6mm
• Stainless Steel - 1.5mm

Fasteners:

• Jamb fixing at 600mm nominal centres.
• Expansion anchors eg. M10 countersunk 'Ramset' Dynabolts
• M12 countersunk masonry screwbolts

Head Fixing (minimum):

• Single door - none required
• Paired door - single central fastener required

Wedging Gap:

• 0-15mm

Frame materials available:

• Timber (any species), Pine clear standard

Fasteners:

• Frame - Screwed (10g x 50mm self tapping) at 600mm nominal centres. Minimum of one screw per location. Frames may also be installed by screw fixing the steel studs to the back of the timber frame during wall construction.
• Stops - nailed (50 x 3.2mm) at 200mm centres.
• Architrave - nailed (50 x 3.2mm) at 400mm centres.

Head Fixing (minimum):

• Single door - none required
• Paired door - single central fastener required

Wedging gap:

• 0-10mm

Frame materials available:

• EGZ - 1.6mm
• Cold rolled galvanized - 1.6mm
• Stainless Steel - 1.5mm

Fasteners:

• Boxed stud riveted with steel pop rivets or screwed with self tapping screws to frame bracing straps at 600mm nominal centres.
• Steel studs may be riveted (steel pop rivets) or screwed (9g x 45mm self tapping) to the frame bracing straps.

Head Fixing (minimum):

• Single door - none required
• Paired door - single central fastener required

Wedging Gap:

• N/A